Messages

1

Others / Re: Swisscom Bluewin-TV KMM3010-SC-B - how to make it alive?

13. Apr 2009, 16:36

Does everybody don't know how to help me? I'm waiting for any clues from couple of days, and there's no answer. I don't have any idea what should I do now.

Is there any chance to do something with this box, or I should put it into trash?

2

Others / Re: Swisscom Bluewin-TV KMM3010-SC-B - how to make it alive?

10. Apr 2009, 19:49

Thanks for interesting in this topic is0-mick!

I've done the same things before you posted, and finally I get JTAG working! In my case the JTAG_enable pins are connected together with a resitor, and on both pins is 3.3V, and there is no connection with the path on SMP chip. So I connected the path with 3.3V source, and it works.
The whole bootloader is readead:

Code: [Select]

CPU Chip ID: 00001000011000110000000000000001 (08630001)
*** Found a SigmaDesigns SMP8634 Rev A CPU chip ***

Issuing Processor / Peripheral Reset ... Done
Halting Processor ... <Processor Entered Debug Mode!> ... Done
Clearing Watchdog ... Done
=========================
Backup Routine Started
=========================

Saving BOOTLOADER_20090410_180901 to Disk...
[ 99% Backed Up]  0x936fff00  (359 bytes/s)
Done  (BOOTLOADER_20090410_180901 saved to Disk OK)

bytes written: 1048576
=========================
Backup Routine Complete
=========================
elapsed time: 2921 seconds


*** REQUESTED OPERATION IS COMPLETE ***

JTAGEMUL: Processor exited debug mode.

I've attached the images extracted from the bootloader, there are included the images with gear wheel and red x sign that I wrote in my first post.

Besides, from some interesting things in the bootloader I found url to the certificate: http://www.scientificatlanta.com/security/pki/crl/msiptve/CA00024_000.crl.htm

It is very plausible that the OS didn't have been fully downloaded yet in the box, I don't know the past of this box.
What are the symptoms of being in disaster recovery mode? If think it is in this mode, because I can run bootloader dumper in every moment after power on.

What are the next steps that I must made to get it working? It is possible in my situation to get it working?

3

Others / Re: Swisscom Bluewin-TV KMM3010-SC-B - how to make it alive?

10. Apr 2009, 12:13

For the disk content, it's all that I found on it.

I have shorted the JTAG_enable jumper, but with no results, the same communicate.
What decides that I must wire an enable pin direcly to the SMP, it is possible to solder to that small circuit?

Does anybody have an idea to make something with the box?

4

Others / Swisscom Bluewin-TV KMM3010-SC-B - how to make it alive?

09. Apr 2009, 18:24

Hello!

From about two weeks I'm owner of Swisscom Bluewin-TV KMM3010-SC-B Set-up box, and I want to make something with it.
In this moment, this box is not very useful, because when I switch power on, only what I get on the screen is a grey gear wheel and something like a progress bar at the bottom, and nothing else.
On the front display while switching on, for a less than second blinks "Starting" message and then only unset clock sign: --:--

I've had an original 160GB HDD from it, but I've gave it to somebody. I've copied all files from it (the file is attached to this post). Now I found 20GB HDD. And my question is: should I make any partitions or the box will make it all?

After few minutes nevermind if it's connected to the internet or not, the screen is showing red x sign, and on VFD display is showing "Connect Fail" message with blinking REC sign. After that in serial console I received "HALTING" message.
Full output from console is:

Code: [Select]


xosPc0 serial#97d634be075d6ca73075760a104d533b subid 0xc4
xenv cs2 ok
Power supply: OK
DRAM0 OK (8)
DRAM1 OK (9)
zboot ok
SIGNED BL

Microsoft IPTV Bootloader, Build (1051)
Built by BM-DELL-167, Sep 11 2006 16:54:12


I've build a JTAG, but I'm receiving this:

Code: [Select]

USAGE: x300tdump
            /start:XXXXXXXX .... custom start location (in HEX)
            /length:XXXXXXXX ... custom length (in HEX)
            /wiggler ........... use wiggler cable

            -----------------------------------------------
Probing bus ... Done

Instruction Length set to 5

CPU Chip ID: 00000000000000000000000000000000 (00000000)
*** Unknown or NO CPU Chip ID Detected ***

Issuing Processor / Peripheral Reset ... Done
Halting Processor ... <Processor did NOT enter Debug Mode!> ... Done
Clearing Watchdog ...

The JTAG is checked many times, all seems to be good. I don't know why it's not working.

When it's connected to ethernet card, all what tcpdump sniffed is saved in a file in the attachment.

Is there any posibility to make something useful with the box? It have a potential, but I don't have now any ideas how to run it.

5

Others / Re: Alternatives for an old x300t

24. Mar 2009, 20:11

It's a good topic to join in. I have a Swisscom Bluewin TV-Box, and I'm trying to do with it something else than IPTV, because I don't have access to the service.
I.e. like vambiro said: streaming video, or playing h.264/xvid videos from usb stick, and recording video from external sources.
I'm wondering if something from this is available to do on that set-up box.