tv2clientCE2

[loneranger]

hi has any one got a patched version of this version number 1.2.xxx666 or any other version as i can't seem to get it to work once complied in vs2008 if not can anyone please offer me some advice on how to decomplie the exe so i can patch it myself

many thanks

[krustykrab]

I to am looking for some advice on this file I have installed a modchip and completed all other steps in the HOW TO, but I am stuck without this file or information on how to patch and recompile it.

Thanks

[vzda]

Hi guys!

I have an X301T device, i patched it successfully. After swiching on, the boot sequence is running, in few minutes in the tv the tv2client appears, and gives an error massage: inicialisation failure, press ok to restart.
What should i change in my device's HDD to run tv2client.exe successfully?
Please write the method step-by-step! (I'd like to use this device as a mediaplayer only) My bootloader version is 1.053.

Thanks for advance!

[jamborl]

Hello everyone!

I have the same problem, ith the initialization problem, and restart.
If someone have a solution for this problem please help me
thank you

[is0-mick]

which box? BT Vision ? X300T? a little bit more info could be helpful....

Mick

[jamborl]

When i get this box the hard was empty. This is a clubinternet K8006 with SMP8634LF. I want only for record DVB-T channels to hard drive, without IPTV or other things what is required internet connection. I've downloaded different packages (htttp..... /PKG.DIR) with PKGTool.exe, but it doesn't start on the box.
The box is run with T-home screen "Please wait ... .
and after a munite message with initilization error and restart button on right part of the screen.
With the other software only a grey gear on the center of the screen.
i don't known is the BT vision or an X300t, but "google" tell me is an x300t compatible box.

[mce2222]

the software does not work if you do not have a t-home internet connection that is IPTV enabled !

it requires patching to fully boot it.

[jamborl]

Do you mean, this paching is with JTAG patching? or it is a simple way for patching the nk.bin or the other part of this software?
In my country i don't have t-online internet connection.
i want to patch the boot , but only if i could manage without JTAG's, it's too difficult for me:( other things (software patching) is no problem...
Can you help me ?
Thank you
Best regards

[is0-mick]

you need hardware (Mochip or Jtag) to patch ANYTHING on the any of these type of boxes.

Mick

[jamborl]

Ok, Thank You very much fpr answers!
I want to get a Moschip or a Jtag, or i want to make one of these, the easiest one.
Please give me some hlep, where i can buy/download scheme/read help, to make my own.
What is the diference the modchip and the eJTAG?

[is0-mick]

eJTAG is the port the mochip connects to.
The schematic and code are on the site...

In this thread here if i remember correctly..
http://www.t-hack.com/forum/index.php?topic=47.0


Mick

[jamborl]

OK.
I have a friend who take out the chip and he can copy the flash from the TV box to the PC, (he has the necesery hardware to make this thing)
My question is:
- which chip is the flash chip (internal flash memory)? on the main board, in the Schematic / board layout the U12 memory? (U12 (A) Flash MX29LV800CBTC-70G (Bios / firmware))
- which patch could i run to patch this flash? and then upload the patched one to the memory, and take back on the mainboard
Have I understand oke?
- and after that what can i have to do to the NK.BIN, i've to running the nkbinpatcher? and i copying to the hard?
Thank you very much.

[is0-mick]

The Flash will most likely be encrypted, and signed. So I dont think its possible to do what you suggest.

The modchip uses jtag to patch the decrypted bootloader in ram. (It gets decrypted from the flash)

I hope that clears things up.

Mick